rem

  1. B

    Gunsmithing Rem 700 - smithing questions

    Finally jumped into the bolt rifle thing. Figure it is time to work on something besides gas guns. My first order of business is machining down the bolt handle for a new knob. Then machining a 20 moa base for it. At the moment I have a couple of questions. 1. What is the average major...
  2. freeflow

    Gunsmithing Threading a REM 700 SPS-V

    HEllo I still new to this form and I just picked up a Rem 700 SPS (.223)Varmint with a 1/12 twist in a 26 inch barrel. My Question is; I would like to send it off to have it threaded for a can and I would like to have it cut down ass well to 18 or 20 inches. And I have seen AR15 barrels set up...
  3. Gilly

    Rifle Scopes Base and rings on rem 5R

    I hate to start a new thread as I am sure it has been covered I cannot find it however. What is the advantage to a one piece base instead of a two piece base setup? I am looking at mounting a scope on my new 5r 300 Win mag and dont want to go the wrong way and waste money. Lots of people seem to...
  4. D

    Tapered base for a Rem 541

    Is anyone here using a tapered base for a Remington 541. Currently my rifle is zeroed at 50yds which is also my max elevation. I have a ton of down but no more up and am thinking that an elevated base would get me where I need to be. thanks in advance dgwelsh
  5. C

    Gunsmithing Rem BDL inlet vs Williams in a McMillan

    Does anyone have means to snap a picture of Remington issue BDL bottom metal sitting in a McMillan stock that has been inlet for Williams bottom metal? Thanks.
  6. bbsj

    Good price for Rem 700 .223 SPS tac

    Is 450.00 a good deal for a Rem 700 .223 sps tac (good condition)
  7. D

    Replacement stock for Rem. VTR

    Thinking about getting a Bell and Carlson Medalist Varminter stock for my VTR. Would like the pro's and con's.
  8. B

    Picked up a rem 700, need opinions.

    I finally broke down and ordered an SPS Tactical in .308 with the hogue stock. It should be here tomorrow. I've got a lot planned for this rifle, but not everything will happen immediately due to funds. The plan is to do a semi-similar build to an M40A3, but not to strict. Anyhow... Right...
  9. JR_V

    Rem 700 SPS-V Beating up brass

    I have a Remington 700 SPS-V .308 that I bought brand new and has not been shot. I made up some dummy training rounds for me to practice cycling the bolt with Winchester brass and Sierra 165's. While doing drills today I noticed that the brass was getting scratched up the length of the body of...
  10. TonyC

    Gunsmithing Rem 700 Old vs. New

    I am gathering parts for my next build and am likely to be using another Rem 700 action as the starting point. Cost aside what are the thoughts between using a recent action vs an older action? Is there anything in favour of an older action from a metalurgical or original machining quality...
  11. gorhamlit

    Photos Rem 700

    These are my gurls
  12. T

    6mm Rem loads

    Looking for some advise on a couple starting powders for the 6mm Rem with a 107 on top of it. Later down the road maybe a 115. Im thinking 4350 or 4831 but wanted to get some ideas from the folks here. Thanks...............
  13. Tribe

    Min/Max 300 Rem SAUM - H4350

    Hey fellas, Looking to run some ladders for the following bullets: 175 SMK 210 SMK 220 SMK 240 VLD If anyone has published Min/Max loads for H4350, I would be much obliged. Thanks much.
  14. mdesign

    Gunsmithing Rem 700 bolt touches barrel ?

    A guy asked me to look at his rifle because it would only shoot 2.5" groups @ 100yds. I noticed the lugs have good equal contact but the side of the nose of the bolt (the dia in front of the lugs) is touching the side of the barrel. Would this make a difference? Some where I was thinking I...
    • mdesign
    • Thread
    • 700 barrel bolt rem touches
    • Replies: 13
    • Forum: The Armory
  15. E

    Rem 700 5R 300 win mag comments?

    Just saw one on guns america for sale and was wondering if anyone has had any experience with one or just have any comments about them. Thanks Eric
  16. MrMike

    My new Rem 700

    All my parts finally came and I got it put together. I do have to send the scope back though. The elevation locking knob was missing its roll pin and dosnt stay in place. Opticsplanet was very easy to deal with on the return and sounded dissapointed that I got a bum product. Locking knob aside...
  17. rockybrashear

    7mm rem mag formula

    hey i just built a 7mm rem mag with a thirty inch barrel that will be pushing 180 gr berger vlds for target shooting. im looking for a good reloading formula to get some good extreme range loads target loads out of this (1200+ yards) anybody got any ideas?
  18. L

    Powders for 260 Rem

    Looking for help, what powder and load do you use for a semi auto rifle 260 Rem using lapuas 123 and 139 scenars. Thanks, Lance
  19. B

    Gunsmithing Rem model 7 help, j-lock, bbl contour, mag boxes,

    Trying to find a replacement firing pin assembly to dump a j-locked one. I have found countless manufacturers for the 700, but none for the 7. Any source other than Remington? Can anyone identify the barrel contour of a non-magnum Model 7? I've found no luck searching. Also, do the...
    • burneyr
    • Thread
    • bbl boxes contour jlock mag model rem
    • Replies: 6
    • Forum: The Armory
  20. L

    Anyone using Berger 175 vld's in Rem 5r?

    I was looking for some info on using Berger 175 vld's in my factory 5r Remington. I am currently using Win. brass Sierra 175mk 41.0g RL15. This load groups arround .5 in, but i am looking to hunt with this setup, and i wanted to try the Berger 175 VLD's (the ones designated hunting)as seirra's...
Top Bottom
Back
Home
Forums
Merch
Alerts